MANHOLE & WATER
VALVE BOX INSERTS

Plastic Manhole Insert
Manhole Insert- V2P
Stainless Steel Insert
Valve Box Insert
Odoreater Insert
Inflow Cost Analysis

MANHOLE REHAB
PRODUCTS

MANHOLE REHAB
APPLICATION EQUIPMENT

MANHOLE CHIMNEY
& JOINT SEALANTS

MANHOLE ODOR CONTROL

VOLUMETRIC WEIRS

PAVING RISERS

ADDITIONAL PRODUCTS
Rap-O Manhole Cover Cushion
Manhole Cover Extractor
Manhole Lid Puller
Manhole Steps

ENGINEERING SPECS

Manhole Rehabilitation Products

The most extensive line of Manhole repair, manhole waterproofing, and
Manhole Rehabilitation products on the market.

Manhole Rehabilitation Products

Select a Manhole Rehabilitation category below
to review our product choices:

Leak Stopping / Patching & Invert Channel Repair / Waterproofing / Linings & Coatings/
Manhole Rehabilitation Application Equipment

Leak Stopping Products for Manhole Rehabilitation

Hydraulic Cement

Parson Quick Plug
Old reliable. Fast-set cementitious product that hardens in about 1 minute to stop small to medium size active leaks.

Urethane Grouts
Parson Hydro Grout

A tough, low viscosity, hydrophobic polyurethane that stops medium to high volume leaks and has controlled reaction times of 30 seconds to 3 minutes.

Parson Multi Grout
A versatile, high viscosity, hydrophobic polyurethane that cures to a flexible foam like a hydrophilic. Can be used with or without accelerator to achieve reaction times from 20 seconds to 1 ½ minutes.

Parson Perma Seal
Our flexible, hydrophilic polyurethane that reacts in about 30 seconds when mixed 1:1 with water.

Parson Seal-Tite
If you need to quickly stop up to 50 gpm of infiltration, this product is for you. Inject the 22 oz. tubes directly into leaks using a dual cartridge caulk gun and watch that leak stop before your eyes.

Dry Oakum
A dry, twisted, jute oakum made in rope form without tar or oil and is backed by laboratory and field research that has made it tops in quality, easy to handle and convenient to use. Available in 10 or 50 lb. boxes.

Injection Ports
Available in 3/8" drive-in style.

Grout Injection Equipment

back to top

Patching / Invert Channel Repair Products
for Manhole Rehabilitation

Parson RPM
A versatile, cementitious, fiber-reinforced, calcium aluminate based product that sets up in approximately 30 minutes. Everything you need in one bucket. Great for patching voids, holes, spalled areas and cracks in manhole walls or for repairing pipe penetrations and the invert or channel.

back to top

Waterproofing Products for Manhole Rehabilitation

Parson Sealcrete
When a manhole is in decent shape, but always seems to be “weeping” water, give this two-coat, brush-on product a try. Easy –to-use premeasured kits that are user friendly and very cost-effective. One of the “original” manhole rehabilitation products.

back to top

Linings/Coatings Products for Manhole Rehabilitation

Parson MH Liner
If manholes need structural rehabilitation due to age or poor construction, our microsilica enhanced, fiber-reinforced cementitious liner is the answer. With application thicknesses up to 3” in a single coat, Compressive Strength over 9000 psi and Bond Strength surpassing 2000 psi, this product is designed to provide a minimum service life of 25 years.

Parson CA Liner 100
In many cases, a manhole damaged by hydrogen sulfide can be rehabilitated with our calcium aluminate based, fiber-reinforced liner. It can be applied up to 2” thick in one coat, has similar physical properties and application methods to our MH Liner.

Parsonpoxy SEL-80
When a calcium aluminate product is just not enough by itself, use our 100% solids epoxy as a topcoat for added corrosion protection. Thicknesses up to 80 mils per coat and designed to provide a minimum service life of 50 years. Easy application using a brush, roller or single pot airless spray equipment.

Parsonpoxy SEL-80HB
An Ultra High Build, 100% solids, corrosion resistant epoxy coating designed as a stand alone coating over brick or precast concrete structures, or as a topcoat over PARSON MH LINER or CA LINER 100. Apply at thicknesses up to 125 mils per coat using a specialized plural component spray equipment.

Flex Liner 1000
A fast set, rapid curing, 100% solids, flexible, two component 100% pure PolyUrea elastomer spray coating material. Its extremely fast gel time makes it suitable for applications down to -20ºF and also produces an extremely tough lining at thicknesses from 10 mils to 1000 mils, without appreciable sag or runs. Surfaces require initial primer coat using Prime Fast.

Manhole Rehabilitation Application Equipment

back to top